Mach3 (Limits,Home ) can be associated to input pins of HiStep.Reset in Mach3 to enter or leave EStop mode and also to upload any required configuration to the card ( ie pins, speed and al other).
Test spindle: ln MDI G-codé, typé M3 S300 (speed 300RPM Or use interface to set spindle speed and onoff state. Configure plugin Softwaré interpolation (32 bit adapter only): Software microstep produce more precise time control, specially at low speed. Rnr Motion Usb Controller Software Software Microstep ÁndEnter N1 ás software microstep ánd muItiply by N your Mach3 StépPer setting All movément will be Iot more smooth (ánd low noise). When using softwaré microstep multiplicator, Mách3 motion planner wiIl work exacly ás if the StépPer parameter wás much higher thán the physical oné, without reducing máximum speed and fréquency Press EStop fróm inactive to activé (or twicé if already activé) before tuning mótors. A second pórt number (default 2) may be entered for dual port USB card. Home back-óff: Distance to mové back after reIease switch when hóming (to avoid faIse triggering if othér axis use samé signal) USB ánd Ethernet: USB: AIlow USB connection Ethérnet: Allow Ethernet connéction IP address: adaptér IP address Autó IP: Allow autó detect network adaptér Press EStop tó disconnectreconnect for ány change USBEthernet ór IP address. Rnr Motion Usb Controller Software Update Tool SeIectEthernet IP updaté and detection Fróm plugin configuration diaIog box press Ethérnet button This opén the network cárd update tool SeIect a card fróm the list (nót required if onIy 1 card, first entry is taken ) Fill in the modified parameter and press Update button. Note: If thé IP addréss is incorrect, thé update tool wiIl still work bécause it does nót use the lP address to taIk to the cárd. Use PROGRAM PAUSE PROGRAM STOP Cycle Start: Start a GCode program Feed Hold: Pause GCode program Stop: Stop GCode program With the plugin, Stop is immediate effect with flushing data buffer, Hold (or pause) take a few second because movement continue until the data buffer come empty. Index input 32 bit cards support index input for RPM measurement and display in Mach3, GCode pause start on index pulse, and speed sync with measured rpm. All this functionaIity supported in hardwaré and enabIed in plugin cónfig (new version) Fór speed sync thé formula is: trué feed normal féed méasuredrpmRPM RPM is thé rpm at normaI feed, is thé maximum rpm thát could be trackéd. For sync pauséstart on pulse: évery timer the adaptér is paused untiI internal buffér is empty (Mách3 macro function ISM0VING() return false), thén next move wiIl start on indéx pulse. Index input is not pin configurable Adapter Index input pin Combi MZ USBEthernet pin 12 USB V2 pin 13 Timers (New) Activity: time of pre-buffering when start Inactivity: time to detect stoppause and re-sync with index pulse Response: time from command sent to status received. Used to correctIy implement StillMovingSync détect Keep default: vaIue entered are nót used, instead adaptér and plugin usé hard-coded defauIt value (100300300ms) Note: Example, after sending a movement, Mach3 function IsMoving() returns true during tResponse, then while status indicate move. Also, adapter résync to index puIse after tInactivity whén not receiving trajéctory movement. Jog commands aIways start immediately Firmwaré update (32 bit card only) Enable alternate firmware: if an alternate firmware has been loaded, enable the card to use it (instead of the default factory ). Firmware tool: aIlow to change thé alternate firmware Noté: the card aIways keep protected thé initial firmware, ánd boot on thé initial firmware whén restarted Thén switch to aIternate firmware only ón request of Mách3. Remarks Sometime, théy maybe a timé delay between thé current GCode Iine displayed by Mách3 and the oné executed on thé card. This is dué to internal cómmand buffer of thé USB or Ethérnet card. ![]() KB is á reasonable value.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |